Home > Cannot Detect > Cannot Detect Ide Drives

Cannot Detect Ide Drives


I suppose i could play around with it, there are several options. Were the Smurfs the first to smurf their smurfs? If I plug it into another IDE port while Windows is running, Windows shudders to a halt and hangs. If you have a CD/DVD drive on this cable - disconnect it (just for testing) and reboot the PC. news

In that case I suggest to reset your BIOS to it's defaults - maybe some setting was accidentally changed or is corrupted causing your SATA controller to be disabled. Try starting the computer with only one drive hooked up at a time. It shut down normal 2 days ago??? Dec 31, 2011 #4 TheBladeRoden TS Rookie Topic Starter Only one has the issue.

Bios Cannot Detect Hard Drive

On startup, the screen should read: Verifying DMI Pool Data Update Successful - The system should continue booting normally. - After the system successfully boots, re-start the PC and access the If it's set any other way, it won't work. My other two hardrives are sata controled by a pci card in raid. That's just thiderastic." -txus.palacios "Clouds are silent, cold, and wet.

I use 40-wire-conductor.. What now? Damage won't be visible.When connecting two IDE devices on one cable you need to jumper one as Master and one as Slave OR both as CS (cable select). Reply Add comment Helpful +6 Report gayasharp 23Posts Saturday October 11, 2008Registration date May 4, 2009 Last seen Oct 13, 2008 11:08PM booting sata hard..i need get ide hard as slave..

This BIOS feature allows you to manually force the BIOS to clear the previously saved ESCD data and reconfigure the settings. I have a MSI motherboard and I do not know if the settings are the same for other boards but to fix it I had to go into the Integrated Peripherals Extract the file into a bootable floppy disk or into hard drive. http://www.overclockers.com/forums/showthread.php/533321-Won-t-detect-IDE-hard-drive Thanks Dayaanand1 August 7, 2012 at 3:40 am If your computer uses the older IDE ports, try checking the jumper settings at the back of the HDD, and CD/DVD drive.

There is a way around it.Your HDD must be the kind that is only used with a special "cable select" cable where the primary must be plugged into the end plug So what's wrong? I have a old 20 gig Western Digital hdd. All Rights Reserved.

Hard Disk Not Detected In Bios How To Recover Data

I would shy away from unhooking your XP drive and then plugging it in as a slave to your linux drive unless you don't care about your XP load. http://ccm.net/forum/affich-29964-ide-cabel-hard-not-detect iDunno, Jan 2, 2004 iDunno, Jan 2, 2004 #3 Jan 2, 2004 #4 Ice Czar Guest Hmmm.... Bios Cannot Detect Hard Drive I set up my boot order proper like, not including the hard drive. Won Idr No, create an account now.

Read more. navigate to this website Does it matter that it has XP loaded on it already? SoCal 16 Oct Story Time With Digi: A Visit to The Pokemon Go Mecca As some of you might know, The Pokemon Go Mecca is The Santa Monica Pier in Santa Reply Add comment Helpful +1 Report gayasharp 23Posts Saturday October 11, 2008Registration date May 4, 2009 Last seen Oct 14, 2008 12:55AM Thanks lot..u hv solve my problem..thanks again..

  1. In the BIOS it should show a boot devices list (maybe called "boot device priority" or "boot order"): HDD; CD-ROM; Stiffy; USB; network - something to that effect with different names
  2. The ESCD area is a special part of your BIOS's CMOS memory, where BIOS settings are held.
  3. Report • #7 GlobalGK January 11, 2010 at 14:22:49 I thought it was windows error with the HD.
  4. Add comment Helpful +3 Report ravi Jan 31, 2009 10:05PM dear sir I have facing problem that my hdd not detect my same computer but the hdd detect other compter I
  5. Both use the ESCD area to read the current status of the hardware and to record changes.
  6. How to iterate over a list using a Regex Wien's oscillator - amplitude stabilization with Zeners (loop's gain) How to tar.gz many similar-size files into multiple archives with a size limit

The message, "Verifying DMI Pool Data" appears and the system hangs. Before bios update take place, download bios file either from Download or ftp://ftp.shuttle.com/ in zip format (file contain, e.g. R U #Hats ! More about the author Im a little afraid of flashing the BIOS.

I booted up into my normal windows( this is where I am as i type). I can't seem to have goo options in BIOS to fix it. iDunno, Jan 2, 2004 iDunno, Jan 2, 2004 #22 Jan 2, 2004 #23 Ice Czar Guest so was I the first time I did it its the consequences of a bad

unlike the Win98SE bootdisk you downloaded you have an Award BIOS here is a little tutorial http://www.cybertechhelp.com/html/tutorials/tutorial.php/id/65 you only need the instructions down to the first line\pagebreak ------------------------------------------------------

The main component of DMI is the Management Information Format Database, or MIFD (the DMI Pool Data). regards, Ian Gregory, Sydney. 0 spralash Apr 2010 edited Apr 2010 To fixe the problem, you need to check whether the earthing for your electic outlet is correct or not. It checks memory, then goes to detect IDE drives and just hangs there and won't go any further. Solution Method One: - Apply power to the computer. - Access the system BIOS. - Set "Reset configuration data" to enable (most likely to be found in PCI/PnP section of BIOS)

Regardless of what I jumper the HDD to, all IDE devices fail when I connect either of the CD drives. The cable with two devices will have a master and a slave. OK HERE IS A LITLE BIT HARDER TO SAY BUT I AM PRETTY SURE WHAT IS...TRY THIS ONE MAKE SURE CABLES ARE SECURELY CONNECTED THEN MAKE SURE ARE PIN 1RED DOT click site As soon as windows starts to load, plug in that molex to power on the IDE drive.

So my jumpers need to be set for master right? To find out more and change your cookie settings, please view our cookie policy. Nothing can be detected in Windows if the BIOS don't see it first.Did you bend a pin in the plugs or plug a cable in backwards? This will entail either: - Removing the "Clear CMOS" Jumper and resetting the system BIOS or: - Obtaining and applying a Flash BIOS Upgrade for your motherboard.

Maybe your cables have gone bad. I'm going to keep looking around to see if anyone else has the same issue and see if I can find a solution. Method Three: - Apply power to the computer. - Access the System BIOS. - Disable both the Internal and External CPU Cache. What stupid thing am i missing?

Not the answer you're looking for? If I connect either CD drive or both of them, nothing IDE runs. Assign it a drive letter and it should appear in my computer. Recent Posts Menu Log in or Sign up [H]ard|Forum Forums > [H]ard|Ware > SSDs & Data Storage > Cannot get across Detecting IDE Drives...

The time now is 02:47 PM. Call the Mod Hotline! Say hello!